Electronics HobbyWing Hobbywing Xr10 Justock G3 Sensored Brushless Esc/Sd G2.1 Motor Combo (17.5T)

Hobbywing Xerun Xr10 Justock G3 &Amp; G2.1 17.5 Turn Motor

The Hobbywing Xr10 Justock G3 Sensored Brushless Esc/Sd G2.1 Motor Combo Has Been Designed With Fixed, 0°, Timing For Spec Class Racing. The Included Sd G2.1 Motor Is An Ideal Stock Motor For Both 1/10 And 1/12 On And Off-Road Racing. These Two Components Paired Together Make For An Ideal Choice For Beginners And Experts Alike.

Features:

• Esc:
• Built-In Polarity Protection. The Xr10 Justock Has Integrated Mosfet’S That If The Battery Terminals Are Connected In Reverse, The Mosfet Will Be Reverse-Biased And Will Not Allow Current To Flow Through The System
• Programmable Via Ota Bluetooth Module Or 3In1 Program Box
• Built-In Capacitor Module Eliminates The Need For External Capacitors And Unwanted Space
• Rpm Speed Limit Function Supports Up To 6 Different Speed, Rpm, Selections To Meet The Needs And Demands Of Various Competitions In The World (Set Through Ota Module Or 3In1 Box)
• Internal Esc Timing Has Been Set To 0 Degrees And Cannot Be Adjusted For Stock Racing
• Built-In Bec Can Support A Maximum Output Current Of Up To 8A. Output Voltage Can Be Set Between 6V Or 7.4V
• Calibration Or Preforming A Factory-Reset Can Be Achieved By Using This Set Button. Simple And Easy To Use
• Supports Both Ccw (Counterclockwise) And Cw (Clockwise) Motor Directions
• Protection Functions Include: Reverse Polarity, Battery Voltage, Esc Temperature, Motor Temperature, Signal Lost And Locked Rotor Protection
• Supports Esc Firmware Upgrades
• User-Friendly And Convenient For Set-Up
• Motor:
• Use Of A Heat-Resistant Magnet Attached Aluminum Case And Double Insulated Windings, High Precision Bearings, And Rotor With A Strong Structure Guarantees Outstanding Performance And Super Durability
• Built-In Hall Sensor Non-Adjustable End Bell Combined With A High Precision And Balanced Rotor Guarantees The User A Smooth And Linear Power On Demand
• Silicon O-Ring Seal Fitted Between The End Bell And Stator Helps To Conduct Inner Heat To The Motor Case And Prevent Dust From Entering The Hall Sensor
• Detachable Structure Design For Daily Cleaning And Maintenance Can Effectively Prolong The Service Life Of This Justock Motor And Improve Its Operating Efficiency
• This Justock Motor Is Applicable To Various 1/10Th, 1/12Th On-Road &Amp; Off-Road Vehicles. It Can Be An Ideal Choice For Stock Or Sport Class Races But Can Also Be A Nice Choice For Newbies For Practice
• The Motor Design Is In Compliance With Ifmar, And Roar Specifications

• Esc:
• Continuous Current: 60A
• Burst Current: 380A
• Battery: 2S Lipo (Only 2S)
• Built-In Bec: 6V/7.4V @ 4A(Switch-Mode)
• Esc Programming: Independent Programming Port
• Motor Supported: Sensor And Sensorless Brushless Motor
• Motor Limit: 10.5T, Or Greater, 3650 Motor
• Application: 1/10, 1/12 On-Road And Off-Road
• Cooling Fan: Powered By Bec
• Size: 40.9X33.9X32.1Mm (Lxwxh)
• Weight: 75.4G (Including Weight Of Wire)
• Motor:
• Scale: 1/10, 1/12
• Brushless: Yes
• Sensored: Yes
• Pole Count: 2
• Kv Rating: 2450
• Lipo Cells: 2-3S
• No-Load Current(A): 3.5
• Outer Diameter: 35.9Mm (1.413″)
• Length: 52.5Mm (2.067″)
• Shaft Diameter: 3.17Mm (0.125″)
• Weight: 176G (6.21Oz)
• Timing: Fixed