Accessories | Parts Realacc Realacc Hubosd Eco X Type W/Stosd8 Current Sensor

Description:

The Hubosd8 Has Been Engineered To Provide The Highest Possible Performance And Reliability In A 46*36Mm &Amp; 4 Layers Pcb.
It Is A Multifunctional Hub With Pdb, Bec 5V/2A &Amp;12V/500Ma, Current Sensor 140A, Stosd8. It Is Specially Made For The Mini Fpv Quad.
The Bec 12V Is Linear Regulator, No Lc Filter Needed. Built-In Stosd8 Can Support Plug &Amp; Play, No Complicated Settings Needed.

Specifications:

• Brand Name: Realacc
• Input Voltage Range (3S-5S Operation): 8 – 21Vdc
• Pdb: 4X30A (Max.4X35A)
• Regulated 5V And 12V Outputs
• Current Sensor 140A
• Built-In Stosd8

Physical:

• 2Oz Copper, 4-Layers &Amp;1.6Mm Pcb.
• 1X Battery Input, 4X Esc Outputs. 2X Bec 5V Outputs, 2X Bec 12V Outputs.
• Camera Signal &Amp; Gnd Pads, Video Transmitter Signal &Amp; Gnd Pads
• 1X Serial Port (Rx, Tx, G)
• Dimensions: 51X36X4Mm, Weight: 9G
• Mounting Holes 30.5Mm Square Spacing, Φ3Mm

Pdb (Esc Outputs):

• Continuous Current: 30A Per Output
• Peak Current (10 Seconds/Minute): 35A Per Output

Bec 5V Outputs:

• Designed For Rc Receivers, Flight Controllers, Osd, And Servos.
• Dc/Dc Synchronous Buck Regulator.
• Voltage: 5.0 +/- 0.1Vdc
• Continuous Current: 2 Amps (Max.2.5A 10S/Minute)
• Output Ripple: 40Mv (Vin=16V, Vout=5V@2A Load)
• Short-Circuit Tolerant (5 Seconds/Minute)

Bec 12V Outputs:

• Linear Regulator, Very Low Noise. Lc Filter Is Needless.
• Designed For Video Tx Or Fpv Camera.
• Voltage: 12.0 +/- 0.3Vdc (4~5S Operation)
• Continuous Current: 500Ma@16V In, 400Ma@20V In
• Short-Circuit Tolerant (2 Seconds/Minute)
• If The Battery Is 3S Lipo, Output Voltage=3S Lipo Voltage – 1V

Current Sensor:

• 140A
• If Current ≫140A. Stosd Display 140A

Stosd8:

• Running Indicator
• Blue Led Blinks: Stosd Is Initializing
• Blue Led Light: Stosd Is Working

Autodetect Pal/Ntsc:

• Auto Sense Pal / Ntsc Cam At Osd Startup. Default Is Ntsc Without Cam Signal

Dynamic On Screen Info:

• Current ≪ 2A &Amp; Keep 5 Seconds Current ≫ 2A

&Nbsp;

Min.Volt &Amp; Max.Amp Recorder
Automatic Flight Timer
Current ≫ 2A, Time In. Current ≪ 2A,Time Out..

Auto Battery Cells Detection
If The Input Voltage Is In The Range Of Following, The Hubosd Will Detect The Cell
Numbers Automatically.
11.1~13.05V: 3Cells Lipo, 14.8~17.4V: 4Cells Lipo, 18.5~21V: 5Cells Lipo
If The Input Voltage Is Out Of The Range. The Voltage Value Will Blink On Screen.
Pls Check If The Battery Total Voltage Is Below 3.7V*Cells

Low Vlotage Alarm:

• (Value Blinks): Default 3.6V* Cells
• Exceeding Mah Alarm
• (Value Blinks): Default 1000Mah

Onscreen Pilot Id:

• Default Is Disable. You Can Type Some Words &Amp; Enable It In Gui

Firmware Up-Gradable:

• Voltage Precision: +/- 0.4%, Voltage Resolution: 0.01V
• Current Precision: +/- 1.5%, Current Resolution: 0.1A